Yongnuo YN-622C Ficha de datos

User Manual

1. Power SwitchPower on when the power switch slides to [ON], channel and group indicators shows that channel and receiving group, power of

4.Flash Test Group Setting (Test + GP SET Button)Set flash testing group Type C camera uses the set firing group.Setting91. H o l d d o w n [ T

When half-pressing the shutter button of the camera, the hot-shoe flash on the receiver will be awakened. (for A/B type camera only)Un

1. Press down [MENU] button on the camera, select flash control-external flash function setting. When the off-camera setting which is

1. Select flash mode as E-TTL II mode.2. Half press camera's shutter button to focus, and on the flash screen the aperture and effectiv

2. 2nd curtain syncThe flash fires right before the shutter closes, lower shutter speed needs to be used, support bulb 2nd curtain sync flash. 1. 1s

2. FEC (Flash Exposure Compensation)button of the camera can also be use.Support 1/3-stop increments to set FEC within ±3. The FEC ※ The sequence

Zoom supports automatic/manual setting.1. With automatic setting, focal length of the flash may change with lens focal length. 2. With manual sett

Manual / Multi Flash Flash161.Manual Flash: Manually set flash output (1/128~1/1 power 1/3-stop increments)Select flash mode as Manual Flash M

17By setting the wireless flash function menu, in a different flash mode or firing group, remotely set A / B / C, three groups of flash

注意事项CONTENTSCautions . . . . . . . . . . . . . . . . . . 1General Description . . . . . . . . . . . . . 2Supported Functions List . . . . . . . . . .

3.Channel Setting via Wireless Function ※ When disabled the wireless function via the camera menu, in transmitting communications, group indicator

Flash Ratio with E-TTL II191.All (A+B+C)R a t i o o f f, A / B / C t h r e e flashes automatically fire with same output, flash e x p o s u re

Manual/Multi Flash Output20Flash output for each group A/B/C can be separately set under Manual/Multi flash mode.1. All (A+B+C)-The three gro

1. Hold down the [CH SET] button for several seconds of the transmitter until the channel indicator blinks for 3 times and then keep

22Type B Cameras:There is no flash control menu of such type of cameras that some of function will be restricted. Enable the mix

Purchase corresponding PC flash sync cord according to the different ports of the flashes needs .1. Use an end of PC sync cord with nut to con

AF Assist Beam EmitterWhen using AF under low-light, the built-in AF-assist beam emitter of the transmitter will be emitted automatic

ReferencesFactory Reset1) Hold down the buttons [CH SET] plus [GP SET] at the same time.2) The state indicators will blink for 3 times in

Troubleshooting1. Fail to power on or automatic shutdown:● The battery is loaded inversely or exhausted; it will power off automatically when the

7. Can't set the flash zoom via camera menu:When the mix control mode has been set in the transmitter (p.21) or zoom locking has b

Please turn off power supplies of all equipment when connecting or installing the product. Please keep it dry. Be sure not to use wet hand t

System type: Digital FSK 2.4GHz wireless transceiverDistance: 100MChannel: 7Flash mode: E-TTL(II), Manual flash, Multi flashSync mode: 1st curtain, 2n

Thank you for purchase the products of Yongnuo firstly. YN -6 22C E -T T L wireles s flash t rigge r is a high performance master and slave

Compatible flash mode: E-TTL (II)/ Manual/ MultiCompatible Shutter sync: 1st curtain, 2nd curtain, high speed sync (HSS/FP), Max 1/8000s sync

List of Type A camerasCanon EOS 5D Mark II/5DMark III,1Ds Mark III,1D Mark IV/1D Mark III,7D,60D, 50D,40D /650D/600D/550D/500D/450D/1100D/1000D List o

Name of Parts※The protective film can be torn out.51).Standby state(red)2).TX communicating state(green blinks)3).RX communicating state(red blinks)AC

1. Installing the Batteries2.Installing the Transceiver on the Camera (As Transmitter)※ Remove the batteries when the product is not used for lon

3.I nstall Flash on the H ot Shoe of the Transceiver (as Receiver)Preparation Before Use71. Install the transceiver on the mini stand or